Instructions 95-8554IR Flame DetectorX98007.2 Rev: 6/10 95-8554
95-855487.2Relay and 0-20 mA Output ModelsFollow the instructions below to install the X9800.Make field connections following local ordinances 1.
9 95-85547.2B2176FIRE ALARM PANELX9800 DETECTORALARM24 VDC+–WIRING NOTES:1 IN NORMAL OPERATION WITH NO FAULTS OCCURRING, THE FAULT RELAY COIL IS ENER
95-8554107.224 VDC4 TO 20 mAPLC–+600 Ω MAXAT 24 VDC–+C2178Oi TEST19876543211918171615141312114-20 mA +4-20 mA + REF4-20 mA –24 VDC +24 VDC – 24 VDC –2
11 95-85547.2EQP ModelConnect external wires to the appropriate terminals 1. inside the device junction box. (See Figure 13 for terminal ident
95-8554127.2Figure 14—A Typical EQP SystemEQP2100PSMSHIELD4 924 VDC –6 724 VDC +5 8B11 3A10 2B 234C 1SHIELD12 1COM2 COM1BUS BAR P3AC LINENHEQPX9800SHI
13 95-85547.2SETTING DEVICE NETWORK ADDRESSES(EQP Models Only)Overview of Network AddressesEach device on the LON must be assigned a unique address.
95-8554147.2STaRTUP PROCEDUREWhen installation of the equipment is complete, perform the “Fire Alarm Test” below. Allow 20 to 30 minutes for the detec
15 95-85547.2maINTENaNCEIMPORTANTPeriodic flamepath inspections are not recommended, since the product is not intended to be serviced and
95-8554167.2fEaTURESResponds to a fire in the presence of modulated •blackbody radiation (i.e. heaters, ovens, turbines) without false al
17 95-85547.2CONE OF VISION—The detector has a 90° cone of vision (horizontal) with the highest sensitivity lying along the central axis. See
DESCRIPTION ...1Outputs ...1LED ...2Optical Integrity (oi) ...
95-8554187.2CERTIFICATION— FMAPPROVED® For complete FM certification details, refer to Appendix A.For complete CSA certification details, refer
19 95-85547.2REPlaCEmENT PaRTSThe detector is not designed to be repaired in the field. If a problem should develop, refer to the Troubleshooting sect
95-8554207.2X9800 MODEL MATRIXMODEL DESCRIPTIONX9800 Single Frequency IR Flame DetectorTYPE MATERIALA AluminumS Stainless Steel (316)TYPE THREAD TYPE4
21 95-85547.2aPPENDIX aFM Approval and Performance ReportTHE FOLLOWING ITEMS, FUNCTIONS AND OPTIONS DESCRIBE THE FM APPROVAL:Explosion-proof for Class
95-8554227.2RESPONSE CHARACTERISTICS:Very High SensitivityLow SensitivityFM Approvals Description and Performance Report – ContinuedHigh Sensitivity*A
23 95-85547.2FALSE ALARM IMMUNITY:High Sensitivity, TDSA On, Quick Fire OffHigh Sensitivity, TDSA On, Quick Fire OffHigh Sensitivity, TDSA On, Quick
95-8554247.2aPPENDIX BCSA CerticationPRODUCTSCLASS 4818 04 - SIGNAL APPLIANCES - Systems - For Hazardous LocationsClass I, Division 1, Groups B, C, a
25 95-85547.2aPPENDIX CATEX ApprovalEC-TYPE EXAMINATION CERTIFICATEDEMKO 02 ATEX 132195XIncreased Safety Model Flameproof Model 0539 FM®II 2 G 0539
95-8554267.2aPPENDIX DIECEx ApprovalIECEx CERTIFICATE OF CONFORMITYDEMKOIECEx ULD 06.0018XEx d e IIC T5-T6 Gb Ex d IIC T4-T6 GbT6 (Tamb =–50°C to
27 95-85547.2aPPENDIX EVdS Schadenverhütung GmbHApprovalVdSPerformance per EN54-10, Certificate of Approval G-203084.EC-Certificate of Conformity08 07
IMPORTANTBe sure to read and understand the entire instruction manual before installing or operating the ame detection system. Any dev
Detector Electronics Corporation6901 West 110th Street Minneapolis, MN 55438 USAT: 952.941.5665 or 800.765.3473F: 952.829.8750W: http://www.det-troni
95-855427.2The Auxiliary relay has normally open / normally closed contacts, and is configurable for energized or de-energized operation, and
3 95-85547.2CAUTIONThese tests require disabling of all extinguishing devices to avoid release resulting from a successful test.The magneti
95-855447.2gENERal aPPlICaTION INfORmaTIONRESPONSE CHARACTERISTICSResponse is dependent on distance, type of fuel, temperature of the fuel, and
5 95-85547.2FACTORS INHIBITING DETECTOR RESPONSEWindowsGlass and Plexiglas windows significantly attenuate radiation and must not be located betwe
95-855467.2INSTallaTIONNOTEThe recommended lubricant for threads and O-rings is a silicone free grease (part number 005003-001) available
7 95-85547.2If conduit is used, we recommend installing drains, according to local codes, at water collection points to automatically
Kommentare zu diesen Handbüchern